![craftsman 5hp shredder blade removal craftsman 5hp shredder blade removal](https://bcsgeorgia.com/wp-content/uploads/2019/04/chippershredder-6.jpg)
The 4 foot long stick (approx 2-3” diameter) disappeared faster than I could follow and it was just.gone. It was so fast and violent it scared the living crap out of me! Push it in to the chipper feed shoot and. Metal “clank” noise is gone now.Īfter it had a chance to get some heat in the engine, I grabbed the other half of the stick I used to test it before the R&R. Sounds 100x better than it did before, which I atribute to freshening up the flails, lubricating everything and balancing all the blades. So at 11 pm, I rolled the chipper out behind the detached garage and fired it up (nearest neighbor is nearly 3 acres away). Balance them all and then reassemble the chipper. Then grinding, filing and stoning the blades to razor sharp edges. I spent the evening tearing the chipper apart. Well, in my typical obsessive fashion, I couldn’t wait until tomorrow. Next winter, I'll probably pull it apart again and give it a nice fresh coat of paint. If I had rented one, that would have been around 50 bucks a day, so if it lasts more than a week (will for sure), I’m money ahead. It's never going to chip up 4-6 inch branches, but it will work fine for my yard clean up purposes. So 250 bucks and a bit of labor and I've got myself (what looks to be) a decent chipper shredder. While doing that, I'll clean it up and put a few other minor bits back to right as well. Tomorrow I'll sharpen and balance the blades, straighten up a few of the metal bits and put it back together. Luckily, they are mirror images front and back, so all I had to do was pull them off, clean them up, lubricate and re-assemble with them flipped around and it's a factory fresh edge again. The profile is damned near worn away on the leading edges and every one of them in generally rounded over. Some are frozen in place (rust) and are discovered to be the source of that metallic “klank” noise I was hearing.You can tell they've never been touched in the way of sharpening or maintenance. They’re in groups of 3 and fling outward when running. There's also 12 metal flails that do the final stage of mulching/shredding on the disc. Result: the light duty blade gets beat to crap. You can tell as the chipper blades dulled and became less and less effective, people had started to jam larger and larger sticks into the mulching section to chop them up. There's a smaller lawn mower type blade on the back of the disc to mulch leaves and twigs and that is also dull as the day is long. A puller wouldn't budge it and i didn't want to be pounding on what is actually the engine crankshaft. The disc is frozen to the engine shaft, so I just decided to leave it be. That metallic “klank” noise fresh in my memory. You can remove just the blades, but I decided to just split the chipper housing and check everything out for good measure. Par for the course in an old used peice of yard equipment. Well, they need sharpening, no real surprise there. They are more like round edged bludgeoning blocks of steel. I shut it down and haul it into the garage to check the chipper blades and discover I'm being generous calling then "blades". And it’s really noisy with a metalic “clank” noise as it spins up or stops. I had to push a finagle it to keep it working on the stick end. But it more beat it to death than chipped it. It starts easily after a few hours sitting in a heated garage. I fire it up at home and run a branch through it to get a baseline for how it does (or doesn't) work. Well, those days are over my old friend I take good care of my stuff and this will be no different. Just hold out as long as it can and then throw it away once dead.īut this old soldier has weathered the abuse well and is still in decent shape, despite obviously minimal care. Used, not well taken care of and just expected to work until it dies. It's a typical piece in the usual condition for used small equipment for the east coast. So 250 bucks changed hands and it was on it's way home with me: The owner ran a couple branches through it and it at least worked. It ran half decent and was a bear to get running, but it was -10c out that day. Only things plastic on it are the wheels, the air cleaner cover and the handle on the pull cord. It's an older model, which means everything is steel. The other day, an older MTD 5 hp one popped up. They were always beat up, overused, neglected and always waaaay than more they were worth.
![craftsman 5hp shredder blade removal craftsman 5hp shredder blade removal](https://m.media-amazon.com/images/I/519Zs4IfqgL._AC_SL1200_.jpg)
But one never popped up locally at a price I wanted to pay. Nothing big, just enough for twigs, smaller branches and leaves. I've been needing a chipper shredder for a while now.